午夜黄色影院_欧美韩国日本一区_日韩av资源站_毛片精品_91午夜激情_先锋影音av资源站

For items described as "Restrictions" or "Usable State" in this manual, the instruction manual iss
the machine tool builder takes precedence over this manual.
Items not described in this manual must be interpreted as "not possible".
This manual is written on the assumption that all option functions are added. Refer to the specific
issued by the machine tool builder before starting use.
Refer to the Instruction Manual issued by each machine tool builder for details on each machine to
Some screens and functions may differ depending on the NC system (or its version), and some fu
may not be possible. Please confirm the specifications before use.
ms related to operation
Before starting actual machining, always carry out graphic check, dry run operation and single bl
operation to check the machining program, tool compensation amount, workpiece compensation
and etc.
If the workpiece coordinate system offset amount is changed during single block stop, the new se
be valid from the next block.
Turn the mirror image ON and OFF at the mirror image center.
If the tool compensation amount is changed during automatic operation (including during single b
stop), it will be validated from the next block or blocks onwards.
ms related to programming
The commands with "no value after G" will be handled as "G00".
";" "EOB" and "%" "EOR" are expressions used for explanation. The actual codes are: For ISO: "CR
"LF" and "%".
Programs created on the Edit screen are stored in the NC memory in a "CR, LF" format, but progra
created with external devices such as the FLD or RS-232C may be stored in an "LF" format.
The actual codes for EIA are: "EOB (End of Block)" and "EOR (End of Record)".
When creating the machining program, select the appropriate machining conditions, and make su
the performance, capacity and limits of the machine and NC are not exceeded. The examples do n
consider the machining conditions.
Do not change fixed cycle programs without the prior approval of the machine tool builder.
When programming the multi-part system, take special care to the movements of the programs fo
part systems.
PLC FX1N-24MT-ES/UL
CN1接頭 MR-J2CN1
伺服控制器 MR-J2S-500B4
伺服放大器 MR-J2S-700A4
伺服電機電源用電纜 MR-PWS1CBL10M-A1-L
調制解調器接口模塊 QJ71CMO
對應SSCNET定位模塊 QD75M1
伺服放大器 MR-J3-700B
編碼器接頭套裝 MR-J3SCNS
PLC FX3U-80MR/ES-A
定位模塊 AD75M2
PLC FX2N-16MT-D
存儲器盒 FX3U-FLROM-64L
PLC FX1N-24MT-D
接線端子塊電纜 MR-J2TBL05M
編碼器接頭 MR-J2CNS
編碼器接頭 MR-J3ENCBL10M-A1-L
編碼器電纜 MR-JCCBL10M-L
PLC FX1S-20MT-001
PLC FX2N-80MT-001
PLC FX3U-16MT/ES-A
PLC FX2N-32MR-D
PLC FX2NC-32MT-D/UL
SSCNET Ⅲ 光纖 MR-J3BUS015M
伺服驅動器 MR-J2S-40A
接頭套件 MR-ECN1
模塊 A6ADP-1MC16T
伺服驅動器 MR-J2S-350A4
PLC FX3U-32MT/ES-A
PLC FX1S-14MR-ES/UL